 |
Copied data can be verified
to achieve maximum
reliability. On the fly MD5
or CRC32 hashing
capabilities are available
using the sector-by-sector
copy mode to guarantee exact
replica of the source's data
without modification,
re-arrangement or
corruption. The byte-by-byte
Verification function is
available when using the ICS
Intelligent Copy mode, which
copies only allocated files.
The source's copied data can
be transferred using the
unit’s direct drive to drive
interface or using the
unit’s external Firewire/USB
interface to copy data from
a source's unopened
computer. The IM Solo-3 IT
duplicator supports IDE,
SATA and SCSI hard disk
drives, including ATA Flash
devices. The unit’s advanced
touch screen user-interface
provides ease of use. IM
Solo-3 IT can copy data to
two hard drives
simultaneously without any
speed reduction. Copy from
SCSI to SCSI drives with the
additional purchase of the
FAST SCSI option. |
|
Note: It's
highly recommended to use
the
Hard Drive Shield
and Coolers
with the Solo 3 IT. This
accessory will protect the
hard drive from EMI noise
while you clone hard drives
and will reduce heat
build-up of the hard
drives. |
|
Features: |
|
|
MD5 and CRC32 Hashing: Simultaneous MD5 and CRC32 hashing generation can be performed during
the data copy opration.
(Note: Hashing is
supported using the
sector-by-sector copy mode
only)
Touch Screen User Interface:
The unit’s advanced Touch
Screen User Interface and
programmed keyboard provides
for ease of use.
High Speed Operation:
Data copied at transfer
rates that exceed 3GB/min.
Built in Write Protection:
Source's data is protected
with built-in write
protection.
Built in FireWire 1384B and
USB 2.0 Interface:
Copy data from a Source's
unopened Notebook or PC.
Also, safely preview the
Source's drive while
connected to the IM Solo-3's
write protected port.
Copy to Two Target Drives
Simultaneously: Copy
data to two hard drives
simultaneously at high
speeds, without speed
reduction.
Multiple Copy Methods: Copy
data using a
sector-by-sector copy
mode or using the ICS'
Intelligent Copy mode, which
copies only allocated files.
WipeOut:
Sanitize drives and erase
data at speeds greater than
3GB/min.
Multiple Media Support:
Supports data transfer
between P-ATA, S-ATA and
SCSI hard disk drives (Note:
SCSI drives are supported
with optional hardware).
Also supports imaging data
from flash media devices and
Notebook drives.
Upgradable:
Software and Firmware
upgrades performed using the
supplied Compact Flash Card.
eSATA:
Supports eSATA drives with
proper 3rd party
SATA-to-eSATA data cable |
|
Software: |
|
|
The following Software
features come standard with
the IM Solo-3 IT unit:
Device Configuration Overlay
(DCO) Option:
DCO can be used to hide and
protect a portion of the
drive’s area from the
operating system and file
system. If DCO is detected
on a Source's drive, the IM
Solo-3 IT's copy operation
will copy the DCO hidden
sectors.
Host Protected Area (HPA)
Option: An
HPA area may exist on a
drive, hiding a certain
portion of the drive’s
contents from the operating
system and file system. If
an HPA area exists on a
Source's drive, the IM
Solo-3 IT's copy operation
will detect and copy data
from the HPA area.
WipeOut DoD Option:
WipeOut was designed to meet
the U.S. Department of
Defense specification DOD
5220-22M regarding the
sanitization of hard disk
drive data. Three
iterations are performed to
completely erase data and
the contents of a hard disk
drive. Each iteration makes
two write passes over the
entire drive.
WipeOut Fast Option:
The WipeOut Fast option
provides a quick non-DoD
method of sanitizing a drive
of all previously stored
data.
LinkMASSter Application:
The LinkMASSter application,
combined with the unit’s
built-in FireWire/USB
interface, provides a fast
and effective solution to
acquire data from a Source's
unopened PC or Notebook to a
Target's drive connected on
the IM Solo-3 IT unit.
MultiMASSter Option:
The MultiMASSter option
allows the user to store up
to 24 s/w loads on a single
master drive, eliminating or
reducing the need for
multiple master drives. |
|
Options: |
|
|
Fast SCSI Option (factory
installed at time of Solo 3
purchase):
Allows you to copy directly
from one SCSI drive to
another SCSI drive at
transfer rates exceeding 4GB
per minute. Optional
Adapters will also allow
copy from SCSI to P-ATA or
S-ATA drives.
Fast SCSI Option (purchased
as an upgrade after
delivery):
Allows you to copy directly
from one SCSI drive to
another SCSI drive at
transfer rates exceeding 4GB
per minute. Optional
Adapters will also allow
copy from SCSI to P-ATA or
S-ATA drives.
SCSI to SATA Adapter:
Allows you - with Fast SCSI
option installed - to copy
directly from one SCSI drive
to another SATA drive.
SCSI to IDE(P-ATA) Adapter:
Allows you - with Fast SCSI
option installed - to copy
directly from one SCSI drive
to another IDE drive.
Notebook Drive Adapters:
ICS proprietary Notebook
drive adapters enables the
IM Solo-3 IT to support a
variety of Notebook models.
CF Adapter:
The Flash adapter was
designed to support 50-pin
micro-drive devices.
Customized Hard Case:
The ruggedized case is
airtight and waterproof to
provide an organized and
protective transport
solution for your IM Solo-3
IT unit.
Hard Drive Coolers:
Protect hard drives from EMI
noise and reduce the hard
drive heat. |
|
Specifications: |
|
|
Supply Voltage:
90 - 230V / 50 - 60 Hz
Power Consumption:
10W without drives
Operating Temperature:
5 degrees - 55 degrees C
Relative Humidity:
20% - 60% non-condensing
Net Weight:
2.2 lbs
Overall Dimensions:
8.3" x 5.8" x 2.2"
Power Supply:UL
and PSU Certified and
Universal Auto-Switching
input voltage |
